10 Kia Picanto Key Fob Replacement Tricks All Experts Recommend

How to Replace a Kia Sportage Replacement Key

The key on many Kia models comes with an entry system that is keyless into. The key functions like the remote control, and can be exchanged with a Kia dealer.

Key fobs are prone to malfunction for several reasons, including an empty coin battery worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key working again.

How do you replace the remote key or smartkey

It doesn't matter if your kia ceed key fob replacement comes with an intelligent key, remote key, push to start key or a regular non-transponder metal key, the battery in these keys will eventually require replacement. This is especially relevant if your vehicle shows a message that states the smart or remote keys aren't powered.

It's a fairly simple procedure. To replace the battery in the keyfob remove the mechanical key from the slit at the back of the fob. Then, push the cover off. Inside the key fob will be an incredibly small screw that holds the battery in place. Remove the old battery by removing the screw with the help of a small screwdriver. Install the new battery and close the gap on the key fob.

Test the key fob by pressing the lock and unlock buttons. It's good If the doors lock and unlock as expected. You can now make use of Kia's hands-free lock/unlock function whenever your fingers get chilly or you have to make errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a computer that is only available to the automotive locksmith or dealer. Other keys (non transponder keys made of metal) don't require programming. If your key needs to be programmed again, you must be aware of the key code number stamped on the key code tag and record the number in a secure place.

How to replace a battery

If the Kia key fob is unable to respond to pressing the lock or unlock button, it's likely that the battery is low. A weak battery could cause other issues, such as the check engine light flashing or the engine not working correctly. It is fairly easy to replace the key fob batteries with only a few simple tools.

Before beginning the process ensure that your vehicle is turned off and that all doors are shut. Locate the small metal or plastic piece on the bottom of your key fob, and jiggle it until a metal key pops out. Then, you can insert this key into the handle of the door for the driver to unlock your car.

To replace the key fob's battery, remove the cover on the rear and use a plier bar tool to remove the latch holding the black negative battery cable. Remove the old battery, and then align the new battery in a way that the "+" positive side faces you, and the "negative" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid bending or damaging the contacts on the metal.

Once the new battery has been installed and the key fob is turned on, turn it off and then on in the ignition for a few times until the door locks cycle. Then, you can test your kia ceed key fob replacement key fob to see if it is working properly again.

How do you replace a keyless key

You can have a standard keyfob or a Smart Key based upon the model of Kia Sportage. The difference between these is that the smart key comes with the small blade of a key in it, whereas the standard fob does not. Both kinds of key fobs contain batteries which eventually needs to be replaced. Luckily, this is an easy process that takes just two minutes.

Before you get started, you will want to ensure that you're on a flat surface with good lighting and that your Kia is turned off. Keep in mind that there are tiny parts inside the fob that could fall out if not vigilant.

The release button for the small size is located on the lower backside. This will either be an oval silver button or a rectangular slot. Once you press this, the mechanical key blade will be released and you can then open the key fob.

Once you have the key fob open, you can simply remove the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After installation it should be possible to lock and unlock your vehicle with your key fob, even if your engine isn't running!

How to replace a mechanical key

The 2013 Kia optima Key Replacement key fob is a wonderful feature that lets us lock and unlock our vehicle with the click of a button. But like any device it will encounter issues at times. There are ways to address these issues and keep your key fobs running for a long time.

One of the most common problems is a weak or dead battery. This could cause your device to stop working or operate intermittently. If this is the case you should replace the battery a new one.

If this doesn't fix the issue Try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to harm any internal components or scratch the plastic. Once the battery is removed then replace it with a new one.

Close and open the door using the mechanical key. (Every 2015 kia forte key fob programming fob comes with a spare mechanical key that fits into the slot). Test the key fob to ensure it's functioning properly. If the device isn't functioning, contact a locksmith or dealer to resolve the problem. Make sure they make you an emergency key that can work for all trunk and door cylinders in order to avoid lockouts again.