Kia Picanto Key Fob Replacement 101: The Ultimate Guide For Beginners

How to Replace a 2016 kia optima key replacement Cost Sportage replacement kia key Key

For a variety of Kia models, the key contains an integrated keyless entry system. This key is similar to the remote control and can be exchanged with an Kia dealer.

Key fobs can stop working due to a number of reasons, including an inactive battery, worn out buttons, signal interference or water damage. Here are some guidelines on how to get your Kia Sportage replacement key to function again.

How do you replace the remote key or smart key?

The battery inside your kia rio car key cover's smart key will eventually need to be replaced, regardless of whether it is a remote key or a push-to-start one, or a regular metal key that doesn't have a transponder. This is especially in the event that your car displays a message that the smart or remote key has low battery power.

It's a fairly simple procedure. To replace the battery in the key fob take the mechanical key from the hole in the back of the key fob. Then remove the cover. Inside the key fob will be tiny screws that hold the battery in place. Using a small screwdriver, remove the screw and remove the battery that was in place. Insert the new battery and close the slit on the key fob.

Once the key fob has new batteries and you've tested it, press the locks and unlock buttons. It's good If the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to run errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of metal), do not need programming. If you need to reprogramme your key, you'll need note the key code's number on the key code tag.

How do I replace a battery

If the Kia key fob does not respond to pressing the lock/unlock button, it is most likely that the battery is insufficient. A weak battery can cause other problems like the check engine light flashing on or delayed cranking of the engine. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires only some basic tools.

Make sure to shut off your vehicle and close all doors prior to beginning. Find the small, metal or plastic piece on the bottom of the key fob. Move it until the key falls out. This key can be put into the driver door handle to unlock your car.

To replace the key fob battery, remove the rear cover and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and then orient the new battery so that the "+" positive side faces you, while the "negative" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid damaging or bending the contacts of the metal.

Once the new battery has been installed after which you turn the key fob off and then turn it on in the ignition until the door locks cycle. You can then test the Kia's key fob again to make sure it's working as intended.

How do you replace the smart key

There is a possibility of having the standard keyfob or Smart Key depending on the model of Kia Sportage. The difference between the two is that the smart key is equipped with tiny mechanical key blade tucked inside it, while the standard key fob does not. Both types of key fobs have batteries inside that will eventually need to be replaced. This is an easy process which takes just two minutes.

Before you get started before you begin, ensure that you're on a flat surface with sufficient lighting and that your Kia is off. Keep in mind that the fob contains small pieces that could be thrown off in the event of a mishap.

The release button for the small size is located on the lower backside. It will be a circular button or rectangular slot. When you press it button, the mechanical blade will appear and you can then open the key fob.

After the key fob has been removed, you can remove the old battery. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After installation you should be able to lock or unlock your car using your key fob even if your engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob is a great convenience, allowing us to lock or unlock our car by pressing one button. Like any device, the Kia key fob can occasionally have problems. Luckily, there are methods to solve these issues and keep our key fobs in good working condition for the long run.

A dead or low-quality battery is one of the most common issues. This could cause your device to stop working or work intermittently. If this is the case then replace the battery with an entirely new battery.

If this does not solve the issue, you can use a standard flathead screwdriver to push the fob's casing made of plastic open. Be careful not to damage any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare kia key mechanical key which will fit into the slot). Test the key fob to confirm it's working properly. Contact a dealer or locksmith to solve the issue when the fob still is not working. Make sure they cut you an emergency key that functions across all trunk and door cylinders to avoid lockouts in the future.